How to make a greenhouse out of polycarbonate and profile pipes with your own hands

Do-it-yourself greenhouse made of polycarbonate: a drawing from a profile pipe can be downloaded directly from this material. To take advantage of all the advantages of a greenhouse on your site, but at the same time save money, you often have to tinker independently. Particular attention at the design stage should be given to the material that will be used for the construction of the frame and wall covering.

It is clear that the frame must be durable. Because, first of all, the durability of the greenhouse depends on this indicator in the future. Next is the choice of covering material, because plants are sensitive to the slightest effect of ultraviolet radiation. Excellent performance is shown by a frame made of profile pipes coated with a polycarbonate greenhouse. Consider the main points, how to build such a greenhouse yourself, what nuances to pay attention to, what drawings to use. Other options how to make a polycarbonate greenhouse and profile.

Features of the construction of the profile frame

First of all, it should be noted that the coating of such buildings on the site with cellular polycarbonate is considered extremely effective and practical in the modern world. Among the film and glass, it is polycarbonate that has the best performance properties from which side to look. It passes through itself a sufficient amount of light, but at the same time delays ultraviolet light. There is an air gap that retains and holds heat. Due to the increased humidity, the material does not lose its excellent performance properties.

A frameless greenhouse, if you use polycarbonate sheets for coating, cannot be built. Because, the rigidity of this material still does not allow this. Under its own weight, this has already been tested many times by gardeners in practice, the sheets begin to bend, cracks form on the panels. So, a do-it-yourself greenhouse made of polycarbonate: a drawing from a profile pipe with a photo is needed just in order to properly build the frame. how to build a greenhouse from polypropylene pipes do it yourself.

The advantages of using metal shaped pipes for the frame of this greenhouse:

1. Excellent mechanical strength, which makes the frame reliable. It can withstand the entire plastic walls of the greenhouse, as well as withstand snow loads. If we talk about some maximum load indicators, then we can note up to 300 kilograms per square meter.
2. The problems of placing powerful lighting and heating equipment with such a strong frame also ceases to be a problem. You can safely operate the building not only directly in the garden season, but even in winter.
3. Assembly, and then subsequent maintenance takes little time and does not take almost any strength.

Important! As for the shortcomings, they, of course, are available. First of all, it should be noted the rather high cost of the material, as well as the need for installation to use special tools to bend the pipes into the soul.

Types of greenhouses with a tube frame

Rectangular (gable crash)

Outwardly, such greenhouses resemble an ordinary house and they are quite common among gardeners.The construction pluses include a large amount of free space inside, which means that you can grow tall plants both in the central part of the greenhouse and along the walls.

Rectangular tunnel

In this design, the roof will be flat and this will save on the stage of construction of the greenhouse. But the minus of such savings is that there will be less space inside. A horizontal crash is also dangerous because in winter it accumulates snow. Polycarbonate, as mentioned in this material, can withstand heavy weights, but you still have to remove snow in winter. Because, due to internal heat, snow can become ice, and then its mass will increase significantly.

Arched

To build such a greenhouse, you need not only a lot of pipes, but also a special pipe bender, because it is impossible to bend a metal pipe yourself into an arc.

To build this type of greenhouse, pipes with a section of 20 * 20 mm or 20 * 40 mm are taken. The second version of the pipes has an additional margin of safety and can be used for structural elements.

Metal pipes have a sufficiently high mass and not always justified cost for the construction of a simple greenhouse in the garden. So that pipes of larger diameter can be safely taken for tropil and supporting walls, and in the remaining sections use smaller and cheaper pipes.

Stage of construction preparation

On the video you can familiarize yourself in detail with the process of how to make a greenhouse with your own hands from polycarbonate, drawings from a profile pipe in a large number of options are presented in this article, but still the final sizes will need to be chosen specifically for you.

As for the initial preparatory stage, it will be necessary to find a suitable place for the future greenhouse. However, here experts say that the metal frame is so strong that it will stand well anywhere on the site. Such a frame will cope with wind loads, it does not require additional protection of capital walls or garden trees.

As for the properties of the soil, it must be additionally taken into account. There should not be too much moisture in the soil under the greenhouse. It is best to choose a site with the most dry soil, with a high content of sand in it. If the kidney is too clay, then soon the area may become marshy. The long side of the structure should be facing south. So it turns out at a maximum angle every day to capture sunlight, plus everything you need to add the reflection of sunlight in the material.

When the construction site on the site is clearly and correctly defined, you need to think about the dimensions of the greenhouse and begin to adjust the already selected drawing to the specific situation. A drawing with dimensions is required, so it will turn out to build a reliable and durable design without errors.

Advice! Do-it-yourself greenhouse made of polycarbonate: a drawing from the profile pipe of the houses, the corner of the roof can not be made too round. Because, the efficiency of the greenhouse will be reduced by increasing the percentage of reflected sunlight.

These are the fundamental points of preparation. Look at the video for this material to the advice of professionals who have already built greenhouses of this kind on the site. In the video tutorials, it will be possible to clearly and accurately understand how exactly one or another stage of the work should be carried out.